- Postcode district
- HA8
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 4–6 weeks for aluminium, 6–8 weeks for slimline or lift and slide corners, from survey sign-off
- Guide price
- From £8,695 inc VAT
- Nearby
- Mill Hill, Hendon, Finchley
- Building rules
- England
Corner sliding doors in Edgware: what to know
The right door depends on the opening, the room and the way you use the garden. Here is how corner sliding doors tend to work out in practice:
Where steel for an Edgware corner extension would bear on a shared wall, the Party Wall etc. Act 1996 (England and Wales) may apply, so it is worth raising with neighbours early.
On any corner installation in Edgware, the survey records floor and patio levels along both walls, because a terrace that falls differently on each side changes the threshold detail.
- Because panels slide rather than fold, the corner can be opened on one side only, keeping the other side closed as a wind screen on cooler days.
- With no post at the corner, sliding both sets of panels back opens the meeting point of two walls completely, so the room spills straight onto the patio.
- Daylight reaches the room from two directions, which keeps a deep extension brighter through the day as the sun moves round the house.
Light and sun in Edgware
Sun angles matter for big glazed doors. Around Edgware, midday sun reaches about 62° in summer and drops to about 15° in winter. That low winter sun is free heat through south-facing glass; high summer sun is easier to shade with a roof overhang, and solar-control glass helps where there is none.
Corner sliding doors prices in Edgware
Pricing does not change because you are in Edgware: the ranges below include fitting, structural calculations and VAT. The steelwork that supports the corner is designed by the engineer and priced after survey, because it depends on the building.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 3.0 m | 4 panels | £8,695–£10,595 |
| 4.0 m | 4 panels | £10,295–£12,495 |
| 4.8 m | 4 panels | £11,495–£13,995 |
See every size on the corner sliding doors page or try the guide price tool.
Survey, manufacture and fitting around Edgware
A surveyor visits your Edgware home to check the wall, the structure above and the floor levels, and talks through glass and finish. Any building work is planned to the engineer's design, the door is made to the finished opening sizes — typically 4–6 weeks for aluminium, 6–8 weeks for slimline or lift and slide corners, from survey sign-off — and fitting usually takes 1–2 days for the door, after 3–5 days of structural building work.
Do you need approval in Edgware?
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Choosing the specification
- Panel layout. Two panels per side for smaller corners or three per side for wider ones, with fixed panels at the far ends.
- Threshold. Standard, low or flush thresholds, with drainage detailed along both elevations.
- Colours. Single or dual colour powder coating, so the outside can match the extension cladding or render.
Questions about corner sliding doors in Edgware
Is the price different in Edgware?
No. Guide prices for corner sliding doors are the same across mainland Britain, including Edgware. The fitted price depends on size, system, glass and finish, and any structural work, all fixed in your written quote after survey.
Can I add a corner sliding door to an existing house?
A corner sliding door can be added to an existing house, but it is a structural project rather than a door swap: the corner of the building has to be rebuilt with engineered steel to carry the load where the post or wall used to be. It is usually done as part of an extension or rear remodel, and a survey plus an engineer's assessment confirm what the structure above needs.
How long does a corner sliding door project take?
A corner sliding door typically takes 4–6 weeks to manufacture in standard aluminium and 6–8 weeks for slimline or lift and slide systems, from survey sign-off. The steelwork and building work usually take 3–5 days before the door goes in, and fitting the door takes 1–2 days. Engineer design and approvals come first, so the door is ordered once the steel is designed.
Do corner sliding doors need a steel beam?
Corner sliding doors almost always need engineered structural support, because removing the corner post takes away the support for the wall or roof above. A structural engineer designs a cantilevered beam or steel frame; the calculations are included in our guide prices and the steelwork is priced after survey. In England this needs a Building Regulations application and in Scotland a building warrant; Wales and Northern Ireland have their own building control rules.