- Postcode district
- RG19
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Newbury, Basingstoke, Reading
- Building rules
- England
Why choose internal pocket doors in Thatcham?
Here is what to weigh up if you are considering internal pocket doors for a home in Thatcham:
If your Thatcham home has a cramped en suite where the door clashes with the basin, a pocket door is worth measuring for before you consider moving the sanitaryware.
Planning an open-plan kitchen in Thatcham but still want to close it off now and then? A double pocket door gives you both.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
Light and sun in Thatcham
With roughly 7 h 51 min of daylight on the shortest day in Thatcham, rooms in the middle of a house can feel gloomy in winter. A glazed internal door shares light from the brightest room without losing the separation of a closed door.
Guide prices for internal pocket doors in Thatcham
The table shows guide prices for common sizes, supplied and fitted, including VAT. Your exact price is fixed in a written quote once the opening in your Thatcham home has been measured.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
From survey to fitted door in Thatcham
Here is the usual sequence in Thatcham: guide price, free survey, written quote, then manufacture (typically 3–5 weeks after survey sign-off, depending on the door leaf and finish). Fitting typically takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Thatcham?
Fitting an internal sliding or pocket door is not usually notifiable building work in England. Approved Document K treats glass in doors as a critical location, so we only supply safety glass for internal doors. If a wall has to be altered to form a pocket, check first whether it is load-bearing.
Which options matter for internal pocket doors?
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
Questions about internal pocket doors in Thatcham
How soon can you survey in Thatcham?
Surveys in the RG19 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.
How long does it take to fit a pocket door?
Fitting a pocket door typically takes one to two days, depending on whether the wall is stud or masonry and how much needs opening up. New plaster then needs time to dry before it can be decorated. We agree the order of work with you at survey so other trades, such as an electrician or decorator, can be booked around it.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.