- Postcode district
- BT20
- Survey
- Free, area covered by arrangement
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Newtownards, Donaghadee, Holywood
- Building rules
- Northern Ireland
Is an internal pocket door a good fit for your home in Bangor (County Down)?
Before you settle on a door type, it helps to know what internal pocket doors do well and what to check before you order.
Where a Bangor (County Down) house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
Before arranging a survey at your Bangor (County Down) home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
Sunlight, glass and orientation in Bangor (County Down)
In winter, Bangor (County Down) gets about 7 h 14 min of daylight against 17 h 18 min in June. Internal sliding and pocket doors help by keeping openings clear during the day and closing off rooms for warmth in the evening.
Guide prices for internal pocket doors in Bangor (County Down)
Guide prices are the same across County Down. They cover the door supplied and fitted into a prepared opening, including VAT, with options itemised in your quote.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
Survey, manufacture and fitting around Bangor (County Down)
Surveys in the BT20 district are booked at a time that suits you. Lead time is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish; on fitting day the track or pocket is installed, the door is hung and adjusted, and the area is left clean. Fitting usually takes 1–2 days, plus drying time before new plaster can be decorated. Bangor (County Down) is in an area we cover by arrangement: the survey is still free, and survey dates, delivery and any travel cost for delivery and fitting are confirmed in your quote before you order.
Do you need approval in Bangor (County Down)?
Internal door work in Northern Ireland is by arrangement. We use safety glass in glazed doors, and any alteration to a load-bearing wall needs building control approval from your district council.
Choosing the specification
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
Questions about internal pocket doors in Bangor (County Down)
How soon can you survey in Bangor (County Down)?
Survey dates in the BT20 district are arranged individually when we reply to your enquiry. After you approve the written quote, manufacture is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish.
What is an internal pocket door?
An internal pocket door is an interior door that slides into a cavity built inside the wall instead of swinging on hinges. The leaf hangs from rollers on a concealed track at the top of a pocket frame, and the frame is boarded and plastered so the wall looks normal. When the door is open, only its edge and pull remain visible.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.