- Postcode district
- BH2
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Christchurch, Poole, Ferndown
- Building rules
- England
What internal pocket doors offer homes in Bournemouth
Before you settle on a door type, it helps to know what internal pocket doors do well and what to check before you order.
Where a Bournemouth house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
Before arranging a survey at your Bournemouth home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
Planning glass for the light in Bournemouth
Light travels further than you might expect through internal glass. When the noon sun in Bournemouth sits at only about 16° in December, a glazed internal door lets light from a south-facing room reach the back of the house.
Typical costs for internal pocket doors around Bournemouth
Guide prices are the same across Dorset. They cover the door supplied and fitted into a prepared opening, including VAT, with options itemised in your quote.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
Survey, manufacture and fitting around Bournemouth
A surveyor checks the doorway, the wall and the floor in your Bournemouth home and talks through the glass or door finish. After you approve the written quote, the door is made typically 3–5 weeks after survey sign-off, depending on the door leaf and finish, and fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Internal doors are generally outside the Building Regulations notification rules, with two things to watch: we only use safety glazing in glass doors, in line with Approved Document K, and any change to a load-bearing wall needs structural advice and Building Control approval.
Specification choices for internal pocket doors in Bournemouth
- Glazed leaf. A door with safety glass panels that borrows daylight from one room for another.
- Bathroom privacy lock. A hook lock with an emergency release, designed for doors that slide rather than swing.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
Questions about internal pocket doors in Bournemouth
Do I need building approval for internal pocket doors in Bournemouth?
In England a replacement door is a controlled fitting, so compliance is arranged through a competent person scheme installer or Building Control; new openings need a Building Regulations application. We confirm the right route for your property at survey, so the paperwork is in place before fitting.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
Do pocket doors need a floor track?
No, the pocket doors we fit hang from rollers on a top track, so the floor stays clear and level through the doorway. A small guide at the mouth of the pocket keeps the leaf running straight without a groove across the floor. That makes them easy to clean around and suitable where the same flooring runs from room to room.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.