- Postcode district
- FK8
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Bridge of Allan, Dunblane, Alloa
- Building rules
- Scotland
Internal pocket doors in Stirling: what to know
The right door depends on the opening, the room and the way you use the garden. Here is how internal pocket doors tend to work out in practice:
Before arranging a survey at your Stirling home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
Where a Stirling house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
- The door leaf can be chosen to match the other internal doors in the house, such as painted panels, oak veneer or a glazed design, so it does not look out of place.
Light and sun in Stirling
In winter, Stirling gets about 6 h 55 min of daylight against 17 h 39 min in June. Internal sliding and pocket doors help by keeping openings clear during the day and closing off rooms for warmth in the evening.
What should you budget for internal pocket doors in Stirling?
The table shows guide prices for common sizes, supplied and fitted, including VAT. Your exact price is fixed in a written quote once the opening in your Stirling home has been measured.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
What happens when you order internal pocket doors in Stirling?
Surveys in the FK8 district are booked at a time that suits you. Lead time is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish; on fitting day the track or pocket is installed, the door is hung and adjusted, and the area is left clean. Fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in Scotland
In Scotland, fitting an internal sliding or pocket door is usually warrant-free; we use safety glass in glazed doors, and alterations to structural walls need a building warrant.
Options to consider for your internal pocket door
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
Questions about internal pocket doors in Stirling
Can you match other doors and windows in my Stirling home?
Usually, yes. Most aluminium and uPVC systems come in standard RAL colours and finishes, and we can quote dual colour where the inside and outside need to differ. Bring photos of existing frames to the survey.
How much does an internal pocket door cost?
Our guide price for a fitted internal pocket door is £895–£1,595 for a single and £1,695–£2,795 for a double, inc VAT at standard height. Where your door falls in that range depends on the leaf, the hardware, the wall construction and how much making good is needed. The final figure is fixed in a written quote after we have surveyed the wall.
How long does it take to fit a pocket door?
Fitting a pocket door typically takes one to two days, depending on whether the wall is stud or masonry and how much needs opening up. New plaster then needs time to dry before it can be decorated. We agree the order of work with you at survey so other trades, such as an electrician or decorator, can be booked around it.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.