- Postcode district
- TW3
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Twickenham, Richmond, Feltham
- Building rules
- England
Internal pocket doors in Hounslow: what to know
A few practical points decide whether internal pocket doors suit a particular room and opening:
Where a Hounslow house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
Before arranging a survey at your Hounslow home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
- Privacy hook locks made for sliding leaves give a bathroom or en suite a door that locks from inside and can still be released from outside in an emergency.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
Planning glass for the light in Hounslow
Internal glazed doors are mostly about borrowed light. In Hounslow, winter daylight lasts only around 7 h 50 min, so a glass door between a bright extension and a darker hallway or dining room can make a noticeable difference from November to February.
How much do internal pocket doors cost in Hounslow?
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
Survey, manufacture and fitting around Hounslow
A surveyor checks the doorway, the wall and the floor in your Hounslow home and talks through the glass or door finish. After you approve the written quote, the door is made typically 3–5 weeks after survey sign-off, depending on the door leaf and finish, and fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Hounslow?
Internal doors are generally outside the Building Regulations notification rules, with two things to watch: we only use safety glazing in glass doors, in line with Approved Document K, and any change to a load-bearing wall needs structural advice and Building Control approval.
Specification choices for internal pocket doors in Hounslow
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
- Bathroom privacy lock. A hook lock with an emergency release, designed for doors that slide rather than swing.
Questions about internal pocket doors in Hounslow
Do you fit internal pocket doors in Hounslow?
Yes. We survey and fit internal pocket doors in Hounslow and across Greater London, including nearby Twickenham and Richmond. Start with a guide price online or call us, and we will arrange a free survey for a new or replacement door.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
How long does it take to fit a pocket door?
Fitting a pocket door typically takes one to two days, depending on whether the wall is stud or masonry and how much needs opening up. New plaster then needs time to dry before it can be decorated. We agree the order of work with you at survey so other trades, such as an electrician or decorator, can be booked around it.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.