- Postcode district
- SM1
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Carshalton, Morden, Mitcham
- Building rules
- England
What internal pocket doors offer homes in Sutton
Before you settle on a door type, it helps to know what internal pocket doors do well and what to check before you order.
In a Sutton hallway where three or four doors open into the same small space, swapping one or two for pocket doors can stop them colliding with each other.
Before arranging a survey at your Sutton home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
- Top-hung rollers carry the weight of the leaf from above, so there is no floor track to trip over, clean around or catch the vacuum cleaner on.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
How much sun will a door in Sutton get?
Light travels further than you might expect through internal glass. When the noon sun in Sutton sits at only about 15° in December, a glazed internal door lets light from a south-facing room reach the back of the house.
What should you budget for internal pocket doors in Sutton?
The table shows guide prices for common sizes, supplied and fitted, including VAT. Your exact price is fixed in a written quote once the opening in your Sutton home has been measured.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
What happens when you order internal pocket doors in Sutton?
Here is the usual sequence in Sutton: guide price, free survey, written quote, then manufacture (typically 3–5 weeks after survey sign-off, depending on the door leaf and finish). Fitting typically takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Sutton?
Fitting an internal sliding or pocket door is not usually notifiable building work in England. Approved Document K treats glass in doors as a critical location, so we only supply safety glass for internal doors. If a wall has to be altered to form a pocket, check first whether it is load-bearing.
Finishes and extras for internal pocket doors
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
Questions about internal pocket doors in Sutton
Do I need building approval for internal pocket doors in Sutton?
In England a replacement door is a controlled fitting, so compliance is arranged through a competent person scheme installer or Building Control; new openings need a Building Regulations application. We confirm the right route for your property at survey, so the paperwork is in place before fitting.
Do pocket doors need a floor track?
No, the pocket doors we fit hang from rollers on a top track, so the floor stays clear and level through the doorway. A small guide at the mouth of the pocket keeps the leaf running straight without a groove across the floor. That makes them easy to clean around and suitable where the same flooring runs from room to room.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.