- Postcode district
- GU34
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Bordon, Farnham, Basingstoke
- Building rules
- England
What internal pocket doors offer homes in Alton
Before you settle on a door type, it helps to know what internal pocket doors do well and what to check before you order.
Where an Alton house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
Before arranging a survey at your Alton home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
- The door leaf can be chosen to match the other internal doors in the house, such as painted panels, oak veneer or a glazed design, so it does not look out of place.
How much sun will a door in Alton get?
In winter, Alton gets about 7 h 53 min of daylight against 16 h 34 min in June. Internal sliding and pocket doors help by keeping openings clear during the day and closing off rooms for warmth in the evening.
Internal pocket doors prices in Alton
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
From survey to fitted door in Alton
Here is the usual sequence in Alton: guide price, free survey, written quote, then manufacture (typically 3–5 weeks after survey sign-off, depending on the door leaf and finish). Fitting typically takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Internal doors are generally outside the Building Regulations notification rules, with two things to watch: we only use safety glazing in glass doors, in line with Approved Document K, and any change to a load-bearing wall needs structural advice and Building Control approval.
Specification choices for internal pocket doors in Alton
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
- Glazed leaf. A door with safety glass panels that borrows daylight from one room for another.
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
Questions about internal pocket doors in Alton
Is the price different in Alton?
No. Guide prices for internal pocket doors are the same across mainland Britain, including Alton. The fitted price depends on size, system, glass and finish, and any structural work, all fixed in your written quote after survey.
Do pocket doors need a floor track?
No, the pocket doors we fit hang from rollers on a top track, so the floor stays clear and level through the doorway. A small guide at the mouth of the pocket keeps the leaf running straight without a groove across the floor. That makes them easy to clean around and suitable where the same flooring runs from room to room.
Are pocket doors suitable for bathrooms?
Pocket doors work well for bathrooms and en suites, particularly small ones where a swinging door clashes with a basin or toilet. A privacy hook lock with an emergency release gives you a lockable door. Bear in mind that a pocket door does not seal as tightly as a hinged door closing against stops on all sides, so a little more sound can pass through.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.