- Postcode district
- SG8
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Letchworth Garden City, Biggleswade, Saffron Walden
- Building rules
- England
Are internal pocket doors right for your Royston home?
The right door depends on the opening, the room and the way you use the garden. Here is how internal pocket doors tend to work out in practice:
Before arranging a survey at your Royston home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
Where a Royston house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
- The door leaf can be chosen to match the other internal doors in the house, such as painted panels, oak veneer or a glazed design, so it does not look out of place.
- Privacy hook locks made for sliding leaves give a bathroom or en suite a door that locks from inside and can still be released from outside in an emergency.
Light and sun in Royston
With roughly 7 h 44 min of daylight on the shortest day in Royston, rooms in the middle of a house can feel gloomy in winter. A glazed internal door shares light from the brightest room without losing the separation of a closed door.
Internal pocket doors prices in Royston
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
How fitting works in Royston
Surveys in the SG8 district are booked at a time that suits you. Lead time is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish; on fitting day the track or pocket is installed, the door is hung and adjusted, and the area is left clean. Fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Fitting an internal sliding or pocket door is not usually notifiable building work in England. Approved Document K treats glass in doors as a critical location, so we only supply safety glass for internal doors. If a wall has to be altered to form a pocket, check first whether it is load-bearing.
Choosing the specification
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
Questions about internal pocket doors in Royston
How soon can you survey in Royston?
Surveys in the SG8 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish.
How much does an internal pocket door cost?
Our guide price for a fitted internal pocket door is £895–£1,595 for a single and £1,695–£2,795 for a double, inc VAT at standard height. Where your door falls in that range depends on the leaf, the hardware, the wall construction and how much making good is needed. The final figure is fixed in a written quote after we have surveyed the wall.
Do pocket doors need a floor track?
No, the pocket doors we fit hang from rollers on a top track, so the floor stays clear and level through the doorway. A small guide at the mouth of the pocket keeps the leaf running straight without a groove across the floor. That makes them easy to clean around and suitable where the same flooring runs from room to room.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.