- Postcode district
- ME15
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Rochester, Gillingham, Strood
- Building rules
- England
Is an internal pocket door a good fit for your home in Maidstone?
Before you settle on a door type, it helps to know what internal pocket doors do well and what to check before you order.
In a Maidstone hallway where three or four doors open into the same small space, swapping one or two for pocket doors can stop them colliding with each other.
Planning an open-plan kitchen in Maidstone but still want to close it off now and then? A double pocket door gives you both.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- When the door is fully open it disappears into the wall, leaving a clear doorway that makes two connected rooms feel like one larger space.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
How much sun will a door in Maidstone get?
Internal glazed doors are mostly about borrowed light. In Maidstone, winter daylight lasts only around 7 h 52 min, so a glass door between a bright extension and a darker hallway or dining room can make a noticeable difference from November to February.
What should you budget for internal pocket doors in Maidstone?
Guide prices are the same across Kent. They cover the door supplied and fitted into a prepared opening, including VAT, with options itemised in your quote.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
Survey, manufacture and fitting around Maidstone
Surveys in the ME15 district are booked at a time that suits you. Lead time is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish; on fitting day the track or pocket is installed, the door is hung and adjusted, and the area is left clean. Fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Fitting an internal sliding or pocket door is not usually notifiable building work in England. Approved Document K treats glass in doors as a critical location, so we only supply safety glass for internal doors. If a wall has to be altered to form a pocket, check first whether it is load-bearing.
Options to consider for your internal pocket door
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
- Bathroom privacy lock. A hook lock with an emergency release, designed for doors that slide rather than swing.
Questions about internal pocket doors in Maidstone
Do I need building approval for internal pocket doors in Maidstone?
In England a replacement door is a controlled fitting, so compliance is arranged through a competent person scheme installer or Building Control; new openings need a Building Regulations application. We confirm the right route for your property at survey, so the paperwork is in place before fitting.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.