- Postcode district
- ML3
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Motherwell, Bellshill, Wishaw
- Building rules
- Scotland
Are internal pocket doors right for your Hamilton home?
A few practical points decide whether internal pocket doors suit a particular room and opening:
Where a Hamilton house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
Planning an open-plan kitchen in Hamilton but still want to close it off now and then? A double pocket door gives you both.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- Privacy hook locks made for sliding leaves give a bathroom or en suite a door that locks from inside and can still be released from outside in an emergency.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
Planning glass for the light in Hamilton
In winter, Hamilton gets about 7 h 00 min of daylight against 17 h 34 min in June. Internal sliding and pocket doors help by keeping openings clear during the day and closing off rooms for warmth in the evening.
Guide prices for internal pocket doors in Hamilton
Guide prices are the same across Lanarkshire. They cover the door supplied and fitted into a prepared opening, including VAT, with options itemised in your quote.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
From survey to fitted door in Hamilton
Here is the usual sequence in Hamilton: guide price, free survey, written quote, then manufacture (typically 3–5 weeks after survey sign-off, depending on the door leaf and finish). Fitting typically takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Hamilton?
Internal doors do not normally need a building warrant in Scotland. We only supply safety glass for glazed doors, and any change to a structural wall would need a warrant, so we check the wall at survey.
Which options matter for internal pocket doors?
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Glazed leaf. A door with safety glass panels that borrows daylight from one room for another.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
Questions about internal pocket doors in Hamilton
Do you fit internal pocket doors in Hamilton?
Yes. We survey and fit internal pocket doors in Hamilton and across Lanarkshire, including nearby Motherwell and Bellshill. Start with a guide price online or call us, and we will arrange a free survey for a new or replacement door.
What is an internal pocket door?
An internal pocket door is an interior door that slides into a cavity built inside the wall instead of swinging on hinges. The leaf hangs from rollers on a concealed track at the top of a pocket frame, and the frame is boarded and plastered so the wall looks normal. When the door is open, only its edge and pull remain visible.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.