- Postcode district
- LE18
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Oadby, Leicester, Earl Shilton
- Building rules
- England
Is an internal pocket door a good fit for your home in Wigston Magna?
A few practical points decide whether internal pocket doors suit a particular room and opening:
In a Wigston Magna hallway where three or four doors open into the same small space, swapping one or two for pocket doors can stop them colliding with each other.
Planning an open-plan kitchen in Wigston Magna but still want to close it off now and then? A double pocket door gives you both.
- Top-hung rollers carry the weight of the leaf from above, so there is no floor track to trip over, clean around or catch the vacuum cleaner on.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
Planning glass for the light in Wigston Magna
Light travels further than you might expect through internal glass. When the noon sun in Wigston Magna sits at only about 14° in December, a glazed internal door lets light from a south-facing room reach the back of the house.
How much do internal pocket doors cost in Wigston Magna?
Guide prices are the same across Leicestershire. They cover the door supplied and fitted into a prepared opening, including VAT, with options itemised in your quote.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
From survey to fitted door in Wigston Magna
Here is the usual sequence in Wigston Magna: guide price, free survey, written quote, then manufacture (typically 3–5 weeks after survey sign-off, depending on the door leaf and finish). Fitting typically takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Internal doors are generally outside the Building Regulations notification rules, with two things to watch: we only use safety glazing in glass doors, in line with Approved Document K, and any change to a load-bearing wall needs structural advice and Building Control approval.
Specification choices for internal pocket doors in Wigston Magna
- Glazed leaf. A door with safety glass panels that borrows daylight from one room for another.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
Questions about internal pocket doors in Wigston Magna
How soon can you survey in Wigston Magna?
Surveys in the LE18 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
Are pocket doors suitable for bathrooms?
Pocket doors work well for bathrooms and en suites, particularly small ones where a swinging door clashes with a basin or toilet. A privacy hook lock with an emergency release gives you a lockable door. Bear in mind that a pocket door does not seal as tightly as a hinged door closing against stops on all sides, so a little more sound can pass through.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.