- Postcode district
- KT11
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Surbiton, Woking, Kingston upon Thames
- Building rules
- England
Is an internal pocket door a good fit for your home in Cobham?
These are the points a surveyor will go through with you when you choose internal pocket doors for a home in Cobham:
In a Cobham hallway where three or four doors open into the same small space, swapping one or two for pocket doors can stop them colliding with each other.
Before arranging a survey at your Cobham home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
- When the door is fully open it disappears into the wall, leaving a clear doorway that makes two connected rooms feel like one larger space.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
Planning glass for the light in Cobham
Light travels further than you might expect through internal glass. When the noon sun in Cobham sits at only about 15° in December, a glazed internal door lets light from a south-facing room reach the back of the house.
How much do internal pocket doors cost in Cobham?
The table shows guide prices for common sizes, supplied and fitted, including VAT. Your exact price is fixed in a written quote once the opening in your Cobham home has been measured.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
How fitting works in Cobham
A surveyor checks the doorway, the wall and the floor in your Cobham home and talks through the glass or door finish. After you approve the written quote, the door is made typically 3–5 weeks after survey sign-off, depending on the door leaf and finish, and fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Cobham?
Fitting an internal sliding or pocket door is not usually notifiable building work in England. Approved Document K treats glass in doors as a critical location, so we only supply safety glass for internal doors. If a wall has to be altered to form a pocket, check first whether it is load-bearing.
Options to consider for your internal pocket door
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
Questions about internal pocket doors in Cobham
How soon can you survey in Cobham?
Surveys in the KT11 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish.
How long does it take to fit a pocket door?
Fitting a pocket door typically takes one to two days, depending on whether the wall is stud or masonry and how much needs opening up. New plaster then needs time to dry before it can be decorated. We agree the order of work with you at survey so other trades, such as an electrician or decorator, can be booked around it.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.