- Postcode district
- WS9
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Walsall, Great Barr, Sutton Coldfield
- Building rules
- England
Are internal pocket doors right for your Aldridge home?
Here is what to weigh up if you are considering internal pocket doors for a home in Aldridge:
Where an Aldridge house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
Renovating a period property in Aldridge? Pocket doors can take panelled leaves that echo the existing doors, so the change looks considered rather than out of place.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- The door leaf can be chosen to match the other internal doors in the house, such as painted panels, oak veneer or a glazed design, so it does not look out of place.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
Light and sun in Aldridge
Light travels further than you might expect through internal glass. When the noon sun in Aldridge sits at only about 14° in December, a glazed internal door lets light from a south-facing room reach the back of the house.
What should you budget for internal pocket doors in Aldridge?
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
Survey, manufacture and fitting around Aldridge
Here is the usual sequence in Aldridge: guide price, free survey, written quote, then manufacture (typically 3–5 weeks after survey sign-off, depending on the door leaf and finish). Fitting typically takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Aldridge?
Internal doors are generally outside the Building Regulations notification rules, with two things to watch: we only use safety glazing in glass doors, in line with Approved Document K, and any change to a load-bearing wall needs structural advice and Building Control approval.
Finishes and extras for internal pocket doors
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
Questions about internal pocket doors in Aldridge
Can you match other doors and windows in my Aldridge home?
Usually, yes. Most aluminium and uPVC systems come in standard RAL colours and finishes, and we can quote dual colour where the inside and outside need to differ. Bring photos of existing frames to the survey.
How much does an internal pocket door cost?
Our guide price for a fitted internal pocket door is £895–£1,595 for a single and £1,695–£2,795 for a double, inc VAT at standard height. Where your door falls in that range depends on the leaf, the hardware, the wall construction and how much making good is needed. The final figure is fixed in a written quote after we have surveyed the wall.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.