- Postcode district
- DY8
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Brierley Hill, Kingswinford, Dudley
- Building rules
- England
Is an internal pocket door a good fit for your home in Stourbridge?
Here is what to weigh up if you are considering internal pocket doors for a home in Stourbridge:
Planning an open-plan kitchen in Stourbridge but still want to close it off now and then? A double pocket door gives you both.
Renovating a period property in Stourbridge? Pocket doors can take panelled leaves that echo the existing doors, so the change looks considered rather than out of place.
- Top-hung rollers carry the weight of the leaf from above, so there is no floor track to trip over, clean around or catch the vacuum cleaner on.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- Privacy hook locks made for sliding leaves give a bathroom or en suite a door that locks from inside and can still be released from outside in an emergency.
Daylight in Stourbridge and what it means for your glass
In winter, Stourbridge gets about 7 h 40 min of daylight against 16 h 49 min in June. Internal sliding and pocket doors help by keeping openings clear during the day and closing off rooms for warmth in the evening.
Internal pocket doors prices in Stourbridge
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
Timescales for internal pocket doors in Stourbridge
Here is the usual sequence in Stourbridge: guide price, free survey, written quote, then manufacture (typically 3–5 weeks after survey sign-off, depending on the door leaf and finish). Fitting typically takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Fitting an internal sliding or pocket door is not usually notifiable building work in England. Approved Document K treats glass in doors as a critical location, so we only supply safety glass for internal doors. If a wall has to be altered to form a pocket, check first whether it is load-bearing.
Which options matter for internal pocket doors?
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
Questions about internal pocket doors in Stourbridge
Do I need building approval for internal pocket doors in Stourbridge?
In England a replacement door is a controlled fitting, so compliance is arranged through a competent person scheme installer or Building Control; new openings need a Building Regulations application. We confirm the right route for your property at survey, so the paperwork is in place before fitting.
What is an internal pocket door?
An internal pocket door is an interior door that slides into a cavity built inside the wall instead of swinging on hinges. The leaf hangs from rollers on a concealed track at the top of a pocket frame, and the frame is boarded and plastered so the wall looks normal. When the door is open, only its edge and pull remain visible.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.