- Postcode district
- BN11
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Shoreham-by-Sea, Littlehampton, Arundel
- Building rules
- England
Why choose internal pocket doors in Worthing?
Before you settle on a door type, it helps to know what internal pocket doors do well and what to check before you order.
In a Worthing hallway where three or four doors open into the same small space, swapping one or two for pocket doors can stop them colliding with each other.
Before arranging a survey at your Worthing home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
- Privacy hook locks made for sliding leaves give a bathroom or en suite a door that locks from inside and can still be released from outside in an emergency.
Sunlight, glass and orientation in Worthing
Internal glazed doors are mostly about borrowed light. In Worthing, winter daylight lasts only around 7 h 56 min, so a glass door between a bright extension and a darker hallway or dining room can make a noticeable difference from November to February.
How much do internal pocket doors cost in Worthing?
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
What happens when you order internal pocket doors in Worthing?
Here is the usual sequence in Worthing: guide price, free survey, written quote, then manufacture (typically 3–5 weeks after survey sign-off, depending on the door leaf and finish). Fitting typically takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Fitting an internal sliding or pocket door is not usually notifiable building work in England. Approved Document K treats glass in doors as a critical location, so we only supply safety glass for internal doors. If a wall has to be altered to form a pocket, check first whether it is load-bearing.
Options to consider for your internal pocket door
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
Questions about internal pocket doors in Worthing
Is the price different in Worthing?
No. Guide prices for internal pocket doors are the same across mainland Britain, including Worthing. The fitted price depends on size, system, glass and finish, and any structural work, all fixed in your written quote after survey.
How long does it take to fit a pocket door?
Fitting a pocket door typically takes one to two days, depending on whether the wall is stud or masonry and how much needs opening up. New plaster then needs time to dry before it can be decorated. We agree the order of work with you at survey so other trades, such as an electrician or decorator, can be booked around it.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.