- Postcode district
- PO1
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 4–6 weeks for the door after the opening is measured; building work scheduled around approvals
- Guide price
- From £6,595 inc VAT
- Nearby
- Gosport, Fareham, Havant
- Building rules
- England
New and widened openings for sliding doors in Portsmouth: what to know
Before you settle on a door type, it helps to know what sliding doors for new openings do well and what to check before you order.
For homes in Portsmouth that are listed or covered by an Article 4 direction, ask the council about the new opening before paying for structural calculations.
Living in a Portsmouth flat? Structural changes to an external wall almost always need the agreement of the building's owner or the other owners, so speak to them first.
- Temporary propping holds up the wall above while the masonry is cut out, keeping floors, ceilings and the roof safely supported throughout the work.
- The door is measured from the finished opening rather than from drawings, so it fits the opening as built, not as it was intended to be built.
- Making good the reveals and head after the steel goes in leaves a square, plumb opening, which is what a precision-made sliding door needs to run smoothly.
Planning glass for the light in Portsmouth
Daylight in Portsmouth runs from about 7 h 57 min in December to 16 h 31 min in June, with the noon sun at roughly 16° and 63° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
Guide prices for sliding doors for new openings in Portsmouth
Use these guide prices to budget for the whole job in Portsmouth: the door, the steelwork, making good and the engineer's calculations, including VAT. Building Control or warrant fees are charged by the council on top.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.5 m | 2 panels | £6,595–£7,295 |
| 2.4 m | 2 panels | £7,895–£8,895 |
| 3.0 m | 2 panels | £8,795–£9,895 |
See every size on the sliding doors for new openings page or try the guide price tool.
What happens when you order sliding doors for new openings in Portsmouth?
A surveyor visits your Portsmouth home to check the wall, the structure above and the floor levels, and talks through glass and finish. Any building work is planned to the engineer's design, the door is made to the finished opening sizes — typically 4–6 weeks for the door after the opening is measured; building work scheduled around approvals — and fitting usually takes 3–5 days of building work, then 1–2 days to fit the door.
Rules for sliding doors for new openings in England
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Finishes and extras for sliding doors for new openings
- Temporary door or boarding. A secure, weathertight closure while the made-to-measure door is being manufactured.
- Steel beam with padstones. A beam sized by the engineer to carry the wall, floors and roof above.
- Widening an existing door. Removing masonry each side of an old patio door to take a wider slider.
Questions about sliding doors for new openings in Portsmouth
Is the price different in Portsmouth?
No. Guide prices for sliding doors for new openings are the same across mainland Britain, including Portsmouth. The fitted price depends on size, system, glass and finish, and any structural work, all fixed in your written quote after survey.
How much does it cost to widen an opening for sliding doors?
Our guide price for forming or widening an opening is £3,595 for 2.4 m and £4,495 for 4.8 m, covering steel, padstones, making good and structural calculations. The door is priced separately, and Building Control fees are set by your council. All figures are guide prices inc VAT, fixed in a written quote after we survey the wall and see what is above it.
Why does beam deflection matter for sliding doors?
Beam deflection matters because a sliding door needs a straight, level head to run properly. Every beam bends slightly under load, and if it bends too much the frame can be squeezed, making panels stiff or causing them to bind. Telling the structural engineer that a large sliding door will go underneath allows them to design a stiffer beam.
Do I need building regulations to widen a door opening?
Yes, forming or widening an opening is structural work and needs a Building Regulations application in England, supported by structural calculations. Building Control inspects the work, typically including the steel and its bearings. In Scotland a building warrant is needed. Wales and Northern Ireland follow their own building regulations through local authority or district council building control.