- Postcode district
- KA12
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Saltcoats, Troon, Kilmarnock
- Building rules
- Scotland
Why choose external pocket sliding doors in Irvine?
These are the points a surveyor will go through with you when you choose external pocket sliding doors for a home in Irvine:
For an Irvine extension still at the drawing stage, planning the pocket wall now is far simpler than rebuilding a finished wall later.
If the wall beside your Irvine patio opening is free of windows, radiators and sockets, it may be long enough to take a pocket so the panels disappear completely.
- When closed, a pocket door looks like a large-paned slider, with slim meeting stiles and plenty of glass instead of the many frames of a folding door.
- With every panel slid into the wall, the full width of the opening is clear, so the room and terrace join without a fixed panel in the way.
- Open panels are hidden inside the wall rather than stacked in view, keeping the opening clean-lined compared with a bifold stack at one side.
Light and sun in Irvine
Daylight in Irvine runs from about 7 h 02 min in December to 17 h 31 min in June, with the noon sun at roughly 11° and 58° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
What should you budget for external pocket sliding doors in Irvine?
Pricing does not change because you are in Irvine: the ranges below include fitting, structural calculations and VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 1 panel | £6,595–£8,095 |
| 3.6 m | 2 panels | £9,295–£11,395 |
| 4.0 m | 2 panels | £9,895–£12,095 |
See every size on the external pocket sliding doors page or try the guide price tool.
What happens when you order external pocket sliding doors in Irvine?
Nothing is ordered until you sign off the surveyed specification. The door is made from the finished opening sizes (typically 6–8 weeks from survey sign-off), and fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door. If you are in Saltcoats or Troon, the same process and prices apply.
Do you need approval in Irvine?
A new opening in Scotland is warrant work: the council needs structural information for the beam and opening before building starts, and the finished door must meet the Scottish standards.
Choosing the specification
- Internal finish. Plastered, panelled or tiled finishes on the pocket wall, with the access panel set discreetly into it.
- Glass. Double or triple glazed safety glass, with laminated or solar-control units as needed.
- Colours. Single or dual colour powder coating, so the exposed edge of the panel matches the frame inside and out.
Questions about external pocket sliding doors in Irvine
Is the price different in Irvine?
No. Guide prices for external pocket sliding doors are the same across mainland Britain, including Irvine. The fitted price depends on size, system, glass and finish, and any structural work, all fixed in your written quote after survey.
How wide can an external pocket sliding door be?
An external pocket sliding door in our range typically gives a clear opening of about 1.8 m to 6 m, using one panel at the narrow end and two or three panels on wider doors. Wider openings usually use pockets on both sides, or a multi-track pocket so the panels stack inside the wall. Sizes are confirmed after survey and the engineer's design.
How much wall do I need for an external pocket door?
An external pocket door needs a clear length of wall beside the opening at least as long as the panels that slide into it, plus a little for the frame. For a single 2 m panel that means just over 2 m of wall with no windows, radiators, sockets or pipes in it. A two-sided pocket splits the panels between both sides, so each side needs less length.
How do you maintain rollers inside a wall pocket?
You maintain pocket door rollers through the access panel built into the inside of the pocket wall, which lets the track be vacuumed and the rollers adjusted without opening up the wall. Keep the outside drainage channel clear so water cannot back up into the pocket, and run the panels fully in and out now and then. If a panel starts to rub inside the pocket, a small roller height adjustment through the access panel usually cures it.