- Postcode district
- CB7
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Newmarket, March, Cambridge
- Building rules
- England
External pocket sliding doors in Ely: what to know
A few practical points decide whether external pocket sliding doors suit a particular room and opening:
If the only wall beside your Ely opening is shared with a neighbour, check the pocket design and any steel bearing on it early, as the Party Wall etc. Act 1996 (England and Wales) may apply.
For an Ely extension still at the drawing stage, planning the pocket wall now is far simpler than rebuilding a finished wall later.
- Open panels are hidden inside the wall rather than stacked in view, keeping the opening clean-lined compared with a bifold stack at one side.
- Pockets can be formed on one side or both, so a wide opening can part in the middle with panels sliding away in each direction.
- Insulating the pocket wall and sealing the panel edges limits heat loss through the cavity, helping the wall beside the door perform like the rest of the house.
Daylight in Ely and what it means for your glass
The midday sun over Ely ranges from about 14° at the winter solstice to about 61° at midsummer. Low-angle winter light reaches further into a room through a tall door, which is one reason taller panels are worth considering; on south or west walls, pair them with solar-control glass.
Typical costs for external pocket sliding doors around Ely
Pricing does not change because you are in Ely: the ranges below include fitting, structural calculations and VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 1 panel | £6,595–£8,095 |
| 3.6 m | 2 panels | £9,295–£11,395 |
| 6.0 m | 3 panels | £12,895–£15,795 |
See every size on the external pocket sliding doors page or try the guide price tool.
Survey, manufacture and fitting around Ely
Nothing is ordered until you sign off the surveyed specification. The door is made from the finished opening sizes (typically 6–8 weeks from survey sign-off), and fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door. If you are in Newmarket or March, the same process and prices apply.
Do you need approval in Ely?
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Which options matter for external pocket sliding doors?
- System type. Standard aluminium, slimline or lift and slide pocket systems, chosen to suit panel weight and sightlines.
- Glass. Double or triple glazed safety glass, with laminated or solar-control units as needed.
- Colours. Single or dual colour powder coating, so the exposed edge of the panel matches the frame inside and out.
Questions about external pocket sliding doors in Ely
Is the price different in Ely?
No. Guide prices for external pocket sliding doors are the same across mainland Britain, including Ely. The fitted price depends on size, system, glass and finish, and any structural work, all fixed in your written quote after survey.
How much wall do I need for an external pocket door?
An external pocket door needs a clear length of wall beside the opening at least as long as the panels that slide into it, plus a little for the frame. For a single 2 m panel that means just over 2 m of wall with no windows, radiators, sockets or pipes in it. A two-sided pocket splits the panels between both sides, so each side needs less length.
How wide can an external pocket sliding door be?
An external pocket sliding door in our range typically gives a clear opening of about 1.8 m to 6 m, using one panel at the narrow end and two or three panels on wider doors. Wider openings usually use pockets on both sides, or a multi-track pocket so the panels stack inside the wall. Sizes are confirmed after survey and the engineer's design.
Does a pocket in the wall cause heat loss?
A pocket in the wall does not have to cause significant heat loss if it is insulated, lined and sealed as part of the design, and the door itself typically achieves whole-door U-values around 1.2–1.6 W/m²K double glazed. In England, a new door in an existing home with more than 60% glazing must achieve 1.4 W/m²K or better. Wales, Scotland and Northern Ireland have their own energy rules.