- Postcode district
- SA31
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Llanelli, Ammanford, Gorseinon
- Building rules
- Wales
What external pocket sliding doors offer homes in Carmarthen
A few practical points decide whether external pocket sliding doors suit a particular room and opening:
For a Carmarthen extension still at the drawing stage, planning the pocket wall now is far simpler than rebuilding a finished wall later.
If the only wall beside your Carmarthen opening is shared with a neighbour, check the pocket design and any steel bearing on it early, as the Party Wall etc. Act 1996 (England and Wales) may apply.
- Insulating the pocket wall and sealing the panel edges limits heat loss through the cavity, helping the wall beside the door perform like the rest of the house.
- Open panels are hidden inside the wall rather than stacked in view, keeping the opening clean-lined compared with a bifold stack at one side.
- Pockets can be formed on one side or both, so a wide opening can part in the middle with panels sliding away in each direction.
Planning glass for the light in Carmarthen
Daylight in Carmarthen runs from about 7 h 46 min in December to 16 h 42 min in June, with the noon sun at roughly 15° and 62° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
External pocket sliding doors prices in Carmarthen
Pricing does not change because you are in Carmarthen: the ranges below include fitting, structural calculations and VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 2.1 m | 1 panel | £7,095–£8,595 |
| 2.4 m | 2 panels | £7,495–£9,195 |
| 6.0 m | 3 panels | £12,895–£15,795 |
See every size on the external pocket sliding doors page or try the guide price tool.
How fitting works in Carmarthen
Nothing is ordered until you sign off the surveyed specification. The door is made from the finished opening sizes (typically 6–8 weeks from survey sign-off), and fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door. If you are in Llanelli or Ammanford, the same process and prices apply.
Rules for external pocket sliding doors in Wales
In Wales, structural work to form or widen an opening needs Building Regulations approval and structural calculations, and the new door must meet the Welsh energy and safety glazing requirements. The Party Wall etc. Act 1996 may apply where steelwork bears on a party wall.
Which options matter for external pocket sliding doors?
- Glass. Double or triple glazed safety glass, with laminated or solar-control units as needed.
- Pocket side. A single pocket to one side, or pockets on both sides so a wide door parts in the middle.
- Colours. Single or dual colour powder coating, so the exposed edge of the panel matches the frame inside and out.
Questions about external pocket sliding doors in Carmarthen
How soon can you survey in Carmarthen?
Surveys in the SA31 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 6–8 weeks from survey sign-off.
How much wall do I need for an external pocket door?
An external pocket door needs a clear length of wall beside the opening at least as long as the panels that slide into it, plus a little for the frame. For a single 2 m panel that means just over 2 m of wall with no windows, radiators, sockets or pipes in it. A two-sided pocket splits the panels between both sides, so each side needs less length.
How do you maintain rollers inside a wall pocket?
You maintain pocket door rollers through the access panel built into the inside of the pocket wall, which lets the track be vacuumed and the rollers adjusted without opening up the wall. Keep the outside drainage channel clear so water cannot back up into the pocket, and run the panels fully in and out now and then. If a panel starts to rub inside the pocket, a small roller height adjustment through the access panel usually cures it.
How wide can an external pocket sliding door be?
An external pocket sliding door in our range typically gives a clear opening of about 1.8 m to 6 m, using one panel at the narrow end and two or three panels on wider doors. Wider openings usually use pockets on both sides, or a multi-track pocket so the panels stack inside the wall. Sizes are confirmed after survey and the engineer's design.