- Postcode district
- BR6
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Chislehurst, Sidcup, Bromley
- Building rules
- England
Are external pocket sliding doors right for your Orpington home?
The right door depends on the opening, the room and the way you use the garden. Here is how external pocket sliding doors tend to work out in practice:
If the only wall beside your Orpington opening is shared with a neighbour, check the pocket design and any steel bearing on it early, as the Party Wall etc. Act 1996 (England and Wales) may apply.
Solid brick, cavity block or timber frame: the way your Orpington wall is built decides how the pocket is formed, which is why the survey looks at it closely.
- A removable access panel on the inside of the pocket wall lets the rollers be reached and adjusted without opening up the plaster.
- Open panels are hidden inside the wall rather than stacked in view, keeping the opening clean-lined compared with a bifold stack at one side.
- Pockets can be formed on one side or both, so a wide opening can part in the middle with panels sliding away in each direction.
Sunlight, glass and orientation in Orpington
Daylight in Orpington runs from about 7 h 51 min in December to 16 h 37 min in June, with the noon sun at roughly 15° and 62° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
How much do external pocket sliding doors cost in Orpington?
These figures are for the door supplied and fitted, with the engineer's structural calculations, including VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra. Your price is fixed in a written quote after survey.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 2.1 m | 1 panel | £7,095–£8,595 |
| 3.0 m | 2 panels | £8,395–£10,295 |
| 3.6 m | 2 panels | £9,295–£11,395 |
See every size on the external pocket sliding doors page or try the guide price tool.
From survey to fitted door in Orpington
Surveys in the BR6 district are booked at a time that suits you. Once the opening is ready and measured, manufacture is typically 6–8 weeks from survey sign-off; on fitting day the frame is set level and sealed, and the panels are adjusted so they glide properly. Fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door.
Rules for external pocket sliding doors in England
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Choosing the specification
- Threshold. Low or flush thresholds, with the external drainage channel continuing past the pocket.
- Pocket side. A single pocket to one side, or pockets on both sides so a wide door parts in the middle.
- Colours. Single or dual colour powder coating, so the exposed edge of the panel matches the frame inside and out.
Questions about external pocket sliding doors in Orpington
Is the price different in Orpington?
No. Guide prices for external pocket sliding doors are the same across mainland Britain, including Orpington. The fitted price depends on size, system, glass and finish, and any structural work, all fixed in your written quote after survey.
Does a pocket in the wall cause heat loss?
A pocket in the wall does not have to cause significant heat loss if it is insulated, lined and sealed as part of the design, and the door itself typically achieves whole-door U-values around 1.2–1.6 W/m²K double glazed. In England, a new door in an existing home with more than 60% glazing must achieve 1.4 W/m²K or better. Wales, Scotland and Northern Ireland have their own energy rules.
How do you maintain rollers inside a wall pocket?
You maintain pocket door rollers through the access panel built into the inside of the pocket wall, which lets the track be vacuumed and the rollers adjusted without opening up the wall. Keep the outside drainage channel clear so water cannot back up into the pocket, and run the panels fully in and out now and then. If a panel starts to rub inside the pocket, a small roller height adjustment through the access panel usually cures it.
How much wall do I need for an external pocket door?
An external pocket door needs a clear length of wall beside the opening at least as long as the panels that slide into it, plus a little for the frame. For a single 2 m panel that means just over 2 m of wall with no windows, radiators, sockets or pipes in it. A two-sided pocket splits the panels between both sides, so each side needs less length.