- Postcode district
- DE14
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Swadlincote, Ashby-de-la-Zouch, Derby
- Building rules
- England
Is an external pocket sliding door a good fit for your home in Burton upon Trent?
A few practical points decide whether external pocket sliding doors suit a particular room and opening:
For a Burton upon Trent extension still at the drawing stage, planning the pocket wall now is far simpler than rebuilding a finished wall later.
Want the whole width of your Burton upon Trent kitchen open to the garden but prefer the look of sliders to bifolds? A pocket gives you both, at the cost of more building work.
- Insulating the pocket wall and sealing the panel edges limits heat loss through the cavity, helping the wall beside the door perform like the rest of the house.
- Pockets can be formed on one side or both, so a wide opening can part in the middle with panels sliding away in each direction.
- With every panel slid into the wall, the full width of the opening is clear, so the room and terrace join without a fixed panel in the way.
How much sun will a door in Burton upon Trent get?
Sun angles matter for big glazed doors. Around Burton upon Trent, midday sun reaches about 61° in summer and drops to about 14° in winter. That low winter sun is free heat through south-facing glass; high summer sun is easier to shade with a roof overhang, and solar-control glass helps where there is none.
Typical costs for external pocket sliding doors around Burton upon Trent
Guide prices include the door, fitting and structural calculations, including VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 1 panel | £6,595–£8,095 |
| 3.6 m | 2 panels | £9,295–£11,395 |
| 4.8 m | 3 panels | £11,095–£13,595 |
See every size on the external pocket sliding doors page or try the guide price tool.
From survey to fitted door in Burton upon Trent
Surveys in the DE14 district are booked at a time that suits you. Once the opening is ready and measured, manufacture is typically 6–8 weeks from survey sign-off; on fitting day the frame is set level and sealed, and the panels are adjusted so they glide properly. Fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door.
Rules for external pocket sliding doors in England
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Specification choices for external pocket sliding doors in Burton upon Trent
- Internal finish. Plastered, panelled or tiled finishes on the pocket wall, with the access panel set discreetly into it.
- Glass. Double or triple glazed safety glass, with laminated or solar-control units as needed.
- Threshold. Low or flush thresholds, with the external drainage channel continuing past the pocket.
Questions about external pocket sliding doors in Burton upon Trent
How soon can you survey in Burton upon Trent?
Surveys in the DE14 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 6–8 weeks from survey sign-off.
How much do external pocket sliding doors cost?
External pocket sliding doors start from a guide price of £6,595 for a 1.8 m single-panel door, fitted, inc VAT, at standard 2.1 m height, including forming the wall pocket. A 3 m two-panel door is a guide £8,395–£10,295, and a 6 m three-panel door is around £12,895. Wall construction, glass and finish affect the figure, which is fixed in a written quote after survey.
How wide can an external pocket sliding door be?
An external pocket sliding door in our range typically gives a clear opening of about 1.8 m to 6 m, using one panel at the narrow end and two or three panels on wider doors. Wider openings usually use pockets on both sides, or a multi-track pocket so the panels stack inside the wall. Sizes are confirmed after survey and the engineer's design.
How do you maintain rollers inside a wall pocket?
You maintain pocket door rollers through the access panel built into the inside of the pocket wall, which lets the track be vacuumed and the rollers adjusted without opening up the wall. Keep the outside drainage channel clear so water cannot back up into the pocket, and run the panels fully in and out now and then. If a panel starts to rub inside the pocket, a small roller height adjustment through the access panel usually cures it.