- Postcode district
- MK45
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks for slimline systems after check survey sign-off
- Guide price
- From £5,095 inc VAT
- Nearby
- Flitwick, Kempston, Bedford
- Building rules
- England
Why choose sliding doors for extensions in Ampthill?
The right door depends on the opening, the room and the way you use the garden. Here is how sliding doors for extensions tend to work out in practice:
Planning an extension in Ampthill? Send us the drawings before the steel is ordered, so the beam above the doors can be designed with the door in mind.
When your Ampthill extension is going through Building Control, keep the energy information for the doors to hand, as the inspector may ask for it.
- Garden rooms benefit from the same approach, with a door sized to the frame and a header designed to carry the roof without pressing down on the door.
- We provide the structural opening size and fitting tolerances in writing, giving your builder a clear target and avoiding disputes about who measured what.
- Telling the engineer the door type and span early lets them design the beam above it to limit deflection, protecting the smooth running of large sliding panels.
Sunlight, glass and orientation in Ampthill
Sun angles matter for big glazed doors. Around Ampthill, midday sun reaches about 61° in summer and drops to about 15° in winter. That low winter sun is free heat through south-facing glass; high summer sun is easier to shade with a roof overhang, and solar-control glass helps where there is none.
How much do sliding doors for extensions cost in Ampthill?
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 2 panels | £5,095–£6,195 |
| 2.1 m | 2 panels | £5,495–£6,795 |
| 6.0 m | 4 panels | £11,395–£13,895 |
See every size on the sliding doors for extensions page or try the guide price tool.
Timescales for sliding doors for extensions in Ampthill
Surveys in the MK45 district are booked at a time that suits you. Once the opening is ready and measured, manufacture is typically 6–8 weeks for slimline systems after check survey sign-off; on fitting day the frame is set level and sealed, and the panels are adjusted so they glide properly. Fitting usually takes 1–2 days, scheduled to the build programme.
Rules for sliding doors for extensions in England
In England, sliding doors in a new extension are covered by the extension's own Building Regulations application rather than a separate door notification. Approved Document L limits the glazed area: windows, roof windows and doors should not normally exceed 25% of the extension's floor area plus the area of any windows or doors lost to the extension, unless the extra glass is compensated for elsewhere. The doors must also meet the energy and safety glazing standards.
Finishes and extras for sliding doors for extensions
- Two-panel slimline. One sliding and one fixed panel, suiting openings up to around 3.6 m depending on the system.
- Solar-control glass. Coated glass for south- and west-facing extensions prone to summer overheating.
- Corner opening. Sliding panels meeting at a corner with no post, for extensions open on two sides.
Questions about sliding doors for extensions in Ampthill
Do you fit sliding doors for extensions in Ampthill?
Yes. We survey and fit sliding doors for extensions in Ampthill and across Bedfordshire, including nearby Flitwick and Kempston. Start with a guide price online or call us, and we will arrange a free survey for a new or replacement door.
How do I get a level threshold in an extension?
A level or flush threshold in an extension needs the finished floor level inside to be set relative to the door sill and the outside paving before the screed goes down. Outside, a drainage channel is needed across the threshold so rain cannot run in. Our thresholds guide explains the options.
What structural opening size should my builder leave for sliding doors?
Your builder should leave the structural opening size we give in writing for your chosen door, which is the frame size plus a small fitting tolerance on each side and at the head. The exact figure depends on the system and the threshold detail. We confirm it from your drawings early, then check the built opening before the door is made.
Can you measure from drawings rather than the built opening?
We can quote from drawings, but we manufacture from a check survey of the built opening, because real openings often differ slightly from the plans. Making a large made-to-measure door from drawings alone risks it not fitting. If a programme makes that unavoidable, any arrangement and who carries the risk would be agreed in writing first.