- Postcode district
- S18
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks for slimline systems after check survey sign-off
- Guide price
- From £5,095 inc VAT
- Nearby
- Chesterfield, Sheffield, Staveley
- Building rules
- England
Is a sliding door for an extension a good fit for your home in Dronfield?
The right door depends on the opening, the room and the way you use the garden. Here is how sliding doors for extensions tend to work out in practice:
For a garden room at the bottom of a Dronfield garden, think about access: large glass panels need a clear route from the road to the site.
Planning an extension in Dronfield? Send us the drawings before the steel is ordered, so the beam above the doors can be designed with the door in mind.
- We provide the structural opening size and fitting tolerances in writing, giving your builder a clear target and avoiding disputes about who measured what.
- Garden rooms benefit from the same approach, with a door sized to the frame and a header designed to carry the roof without pressing down on the door.
- Setting the finished floor level before the screed goes down allows a low threshold, typically 15–25 mm, or a flush one with a drainage channel outside.
Light and sun in Dronfield
Sun angles matter for big glazed doors. Around Dronfield, midday sun reaches about 60° in summer and drops to about 13° in winter. That low winter sun is free heat through south-facing glass; high summer sun is easier to shade with a roof overhang, and solar-control glass helps where there is none.
Guide prices for sliding doors for extensions in Dronfield
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 2.1 m | 2 panels | £5,495–£6,795 |
| 2.4 m | 2 panels | £5,995–£7,295 |
| 3.0 m | 2 panels | £6,895–£8,395 |
See every size on the sliding doors for extensions page or try the guide price tool.
How fitting works in Dronfield
Surveys in the S18 district are booked at a time that suits you. Once the opening is ready and measured, manufacture is typically 6–8 weeks for slimline systems after check survey sign-off; on fitting day the frame is set level and sealed, and the panels are adjusted so they glide properly. Fitting usually takes 1–2 days, scheduled to the build programme.
Rules for sliding doors for extensions in England
Doors in an English extension go through the extension's Building Regulations approval. Under Approved Document L, the total area of windows, roof windows and doors is normally capped at 25% of the extension's floor area plus any openings the extension removes, unless your designer shows compensating improvements; the glass must be safety glazing under Approved Document K.
Choosing the specification
- Corner opening. Sliding panels meeting at a corner with no post, for extensions open on two sides.
- Two-panel slimline. One sliding and one fixed panel, suiting openings up to around 3.6 m depending on the system.
- Flush threshold. A level floor from inside to out, with a drainage channel set into the patio.
Questions about sliding doors for extensions in Dronfield
Do you fit sliding doors for extensions in Dronfield?
Yes. We survey and fit sliding doors for extensions in Dronfield and across Derbyshire, including nearby Chesterfield and Sheffield. Start with a guide price online or call us, and we will arrange a free survey for a new or replacement door.
When should I order sliding doors for an extension?
Order sliding doors for an extension as soon as the opening is built and a check survey can be done, and agree the target fitting date with your builder in advance. Slimline doors typically take 6–8 weeks to make after sign-off. Getting a quote from drawings early means the specification is settled and only the final measurements are needed.
Why does the steel beam matter for sliding doors?
The steel beam above an extension's sliding door matters because every beam bends a little under load, and a large sliding door needs a straight, level head to run freely. If the engineer knows a wide slider will sit under the beam, they can design for low deflection. Too much movement can make panels stiff or bind.
Can you measure from drawings rather than the built opening?
We can quote from drawings, but we manufacture from a check survey of the built opening, because real openings often differ slightly from the plans. Making a large made-to-measure door from drawings alone risks it not fitting. If a programme makes that unavoidable, any arrangement and who carries the risk would be agreed in writing first.