- Postcode district
- EH42
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks for slimline systems after check survey sign-off
- Guide price
- From £5,095 inc VAT
- Nearby
- North Berwick, Haddington, Duns
- Building rules
- Scotland
Are sliding doors for extensions right for your Dunbar home?
Most homeowners choosing sliding doors for extensions want the same things: more light, a clear view and a door that is easy to live with.
When your Dunbar extension is going through Building Control, keep the energy information for the doors to hand, as the inspector may ask for it.
If your Dunbar builder is about to pour the screed, confirm the finished floor level for the threshold first, because it is very hard to change afterwards.
- We provide the structural opening size and fitting tolerances in writing, giving your builder a clear target and avoiding disputes about who measured what.
- Telling the engineer the door type and span early lets them design the beam above it to limit deflection, protecting the smooth running of large sliding panels.
- Slimline aluminium systems with interlocks typically around 20–25 mm maximise the glass in a new rear wall, keeping the view as open as possible.
How much sun will a door in Dunbar get?
Sun angles matter for big glazed doors. Around Dunbar, midday sun reaches about 57° in summer and drops to about 11° in winter. That low winter sun is free heat through south-facing glass; high summer sun is easier to shade with a roof overhang, and solar-control glass helps where there is none.
Sliding doors for extensions and garden rooms prices in Dunbar
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 2 panels | £5,095–£6,195 |
| 3.0 m | 2 panels | £6,895–£8,395 |
| 4.8 m | 3 panels | £9,595–£11,695 |
See every size on the sliding doors for extensions page or try the guide price tool.
How fitting works in Dunbar
Here is the usual sequence in Dunbar: guide price, free survey, written quote, any building work, then manufacture (typically 6–8 weeks for slimline systems after check survey sign-off). Fitting typically takes 1–2 days, scheduled to the build programme. Nearby, we also survey in North Berwick, Haddington and Duns.
Rules for sliding doors for extensions in Scotland
In Scotland, an extension needs a building warrant before work starts, and the doors are covered by it; the design must meet the Scottish building standards for energy and safety glazing.
Finishes and extras for sliding doors for extensions
- Flush threshold. A level floor from inside to out, with a drainage channel set into the patio.
- Corner opening. Sliding panels meeting at a corner with no post, for extensions open on two sides.
- Solar-control glass. Coated glass for south- and west-facing extensions prone to summer overheating.
Questions about sliding doors for extensions in Dunbar
Can you match other doors and windows in my Dunbar home?
Usually, yes. Most aluminium and uPVC systems come in standard RAL colours and finishes, and we can quote dual colour where the inside and outside need to differ. Bring photos of existing frames to the survey.
Why does the steel beam matter for sliding doors?
The steel beam above an extension's sliding door matters because every beam bends a little under load, and a large sliding door needs a straight, level head to run freely. If the engineer knows a wide slider will sit under the beam, they can design for low deflection. Too much movement can make panels stiff or bind.
What structural opening size should my builder leave for sliding doors?
Your builder should leave the structural opening size we give in writing for your chosen door, which is the frame size plus a small fitting tolerance on each side and at the head. The exact figure depends on the system and the threshold detail. We confirm it from your drawings early, then check the built opening before the door is made.
Can you measure from drawings rather than the built opening?
We can quote from drawings, but we manufacture from a check survey of the built opening, because real openings often differ slightly from the plans. Making a large made-to-measure door from drawings alone risks it not fitting. If a programme makes that unavoidable, any arrangement and who carries the risk would be agreed in writing first.