- Postcode district
- BA12
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks for slimline systems after check survey sign-off
- Guide price
- From £5,095 inc VAT
- Nearby
- Frome, Trowbridge, Bradford-on-Avon
- Building rules
- England
Are sliding doors for extensions right for your Warminster home?
A few practical points decide whether sliding doors for extensions suit a particular room and opening:
Planning an extension in Warminster? Send us the drawings before the steel is ordered, so the beam above the doors can be designed with the door in mind.
If your Warminster builder is about to pour the screed, confirm the finished floor level for the threshold first, because it is very hard to change afterwards.
- Slimline aluminium systems with interlocks typically around 20–25 mm maximise the glass in a new rear wall, keeping the view as open as possible.
- Telling the engineer the door type and span early lets them design the beam above it to limit deflection, protecting the smooth running of large sliding panels.
- A check survey once the opening is built means the door is made to the real dimensions, accounting for any small variation in the brickwork or blockwork.
Sunlight, glass and orientation in Warminster
Daylight in Warminster runs from about 7 h 53 min in December to 16 h 35 min in June, with the noon sun at roughly 15° and 62° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
Typical costs for sliding doors for extensions around Warminster
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 2 panels | £5,095–£6,195 |
| 2.1 m | 2 panels | £5,495–£6,795 |
| 2.4 m | 2 panels | £5,995–£7,295 |
See every size on the sliding doors for extensions page or try the guide price tool.
Timescales for sliding doors for extensions in Warminster
Nothing is ordered until you sign off the surveyed specification. The door is made from the finished opening sizes (typically 6–8 weeks for slimline systems after check survey sign-off), and fitting usually takes 1–2 days, scheduled to the build programme. If you are in Frome or Trowbridge, the same process and prices apply.
Do you need approval in Warminster?
Doors in an English extension go through the extension's Building Regulations approval. Under Approved Document L, the total area of windows, roof windows and doors is normally capped at 25% of the extension's floor area plus any openings the extension removes, unless your designer shows compensating improvements; the glass must be safety glazing under Approved Document K.
Choosing the specification
- Flush threshold. A level floor from inside to out, with a drainage channel set into the patio.
- Two-panel slimline. One sliding and one fixed panel, suiting openings up to around 3.6 m depending on the system.
- Corner opening. Sliding panels meeting at a corner with no post, for extensions open on two sides.
Questions about sliding doors for extensions in Warminster
Can you match other doors and windows in my Warminster home?
Usually, yes. Most aluminium and uPVC systems come in standard RAL colours and finishes, and we can quote dual colour where the inside and outside need to differ. Bring photos of existing frames to the survey.
What sliding doors suit a garden room?
A garden room usually suits a two-panel or three-panel sliding door sized to the front of the building, with a header strong enough to carry the roof without pressing on the frame. Aluminium systems are a common choice because they are stable and need little maintenance. Glass with good insulation helps if the room will be used all year.
What structural opening size should my builder leave for sliding doors?
Your builder should leave the structural opening size we give in writing for your chosen door, which is the frame size plus a small fitting tolerance on each side and at the head. The exact figure depends on the system and the threshold detail. We confirm it from your drawings early, then check the built opening before the door is made.
Can you measure from drawings rather than the built opening?
We can quote from drawings, but we manufacture from a check survey of the built opening, because real openings often differ slightly from the plans. Making a large made-to-measure door from drawings alone risks it not fitting. If a programme makes that unavoidable, any arrangement and who carries the risk would be agreed in writing first.