- Postcode district
- PH2
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 2–4 weeks for uPVC or 4–6 weeks for aluminium, from survey sign-off
- Guide price
- From £1,995 inc VAT
- Nearby
- Auchterarder, Kinross, Blairgowrie
- Building rules
- Scotland
Is a tilt and slide door a good fit for your home in Perth?
The right door depends on the opening, the room and the way you use the garden. Here is how tilt and slide doors tend to work out in practice:
Young children at home in Perth? A sliding restrictor, available on many systems, limits how far the sash opens while still letting air in.
Is the opening in your Perth home wider than about 3 m? If so, tilt and slide hardware will not carry a sash that size, and a lift and slide door is worth comparing.
- Locking points engage around the whole perimeter of the sash, much like a window, rather than only along the closing edge.
- The sash moves forward and slides parallel in front of the fixed pane, so nothing swings into the room and the floor beside the door stays usable.
- A tilt and slide door fits the same kind of opening as an ordinary patio door, so a draughty older slider can often be swapped without building work.
How much sun will a door in Perth get?
Sun angles matter for big glazed doors. Around Perth, midday sun reaches about 57° in summer and drops to about 10° in winter. That low winter sun is free heat through south-facing glass; high summer sun is easier to shade with a roof overhang, and solar-control glass helps where there is none.
Guide prices for tilt and slide doors in Perth
Pricing is transparent and does not change because you are in Perth. The ranges below cover a standard-height door, fitted, with VAT; options are itemised in your quote.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 2 panels | £2,195–£2,695 |
| 2.4 m | 2 panels | £2,595–£3,195 |
| 3.0 m | 2 panels | £2,995–£3,595 |
See every size on the tilt and slide doors page or try the guide price tool.
Timescales for tilt and slide doors in Perth
A surveyor visits your Perth home to measure the structural opening, check levels and the lintel, and talk through glass and finish. Once you confirm the written specification, the door is made to measure — typically 2–4 weeks for uPVC or 4–6 weeks for aluminium, from survey sign-off — and fitting usually takes 1 day for a straight swap in an existing opening. We also cover Auchterarder (20 km south-west) and Kinross (21 km south).
Do you need approval in Perth?
Scottish building standards still apply to a replacement door even where no warrant is needed, so the door must meet the energy and safety glazing requirements. If the opening is being formed or widened, a building warrant is required before work begins.
Options to consider for your tilt and slide door
- Restrictor. A sliding restrictor on many systems to limit the opening for upstairs rooms or homes with young children.
- Colours. White, woodgrain or coloured foils on uPVC; standard or RAL powder coats on aluminium.
- Sash side. A left or right opening sash, chosen to suit furniture, the patio layout and the way you walk out.
Questions about tilt and slide doors in Perth
How soon can you survey in Perth?
Surveys in the PH2 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 2–4 weeks for uPVC or 4–6 weeks for aluminium, from survey sign-off.
How much does a tilt and slide patio door cost?
Tilt and slide patio doors start from a guide price of £1,995 for a 1.5 m two-panel door, fitted, inc VAT, at standard 2.1 m height. A 2.1 m door is a guide £2,395–£2,895, and a 3 m door is around £2,995. Aluminium frames, colour and triple glazing move the figure up, and the final price is fixed in a written quote after survey.
How wide can a tilt and slide door be?
A tilt and slide door in our range is typically about 1.5 m to 3 m wide overall, with one opening sash and one fixed panel. The sash size is set by the hardware's weight limit, which is lower than for inline or lift and slide systems. If you need a wider opening, a standard aluminium slider or a lift and slide door is the usual alternative.
How long does a tilt and slide door take?
A tilt and slide door typically takes 2–4 weeks to make in uPVC and 4–6 weeks in aluminium, from survey sign-off. Fitting typically takes 1 day for a straight swap in an existing opening, including removing the old door and making good. These are typical times rather than fixed promises, and the date is confirmed once the order is placed.