- Postcode district
- HP27
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Aylesbury, Thame, High Wycombe
- Building rules
- England
Are internal pocket doors right for your Princes Risborough home?
A few practical points decide whether internal pocket doors suit a particular room and opening:
Where a Princes Risborough house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
Planning an open-plan kitchen in Princes Risborough but still want to close it off now and then? A double pocket door gives you both.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
- The door leaf can be chosen to match the other internal doors in the house, such as painted panels, oak veneer or a glazed design, so it does not look out of place.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
Planning glass for the light in Princes Risborough
Light travels further than you might expect through internal glass. When the noon sun in Princes Risborough sits at only about 15° in December, a glazed internal door lets light from a south-facing room reach the back of the house.
How much do internal pocket doors cost in Princes Risborough?
The table shows guide prices for common sizes, supplied and fitted, including VAT. Your exact price is fixed in a written quote once the opening in your Princes Risborough home has been measured.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
How fitting works in Princes Risborough
Surveys in the HP27 district are booked at a time that suits you. Lead time is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish; on fitting day the track or pocket is installed, the door is hung and adjusted, and the area is left clean. Fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Princes Risborough?
Fitting an internal sliding or pocket door is not usually notifiable building work in England. Approved Document K treats glass in doors as a critical location, so we only supply safety glass for internal doors. If a wall has to be altered to form a pocket, check first whether it is load-bearing.
Options to consider for your internal pocket door
- Bathroom privacy lock. A hook lock with an emergency release, designed for doors that slide rather than swing.
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
Questions about internal pocket doors in Princes Risborough
How soon can you survey in Princes Risborough?
Surveys in the HP27 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
What is an internal pocket door?
An internal pocket door is an interior door that slides into a cavity built inside the wall instead of swinging on hinges. The leaf hangs from rollers on a concealed track at the top of a pocket frame, and the frame is boarded and plastered so the wall looks normal. When the door is open, only its edge and pull remain visible.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.