- Postcode district
- PH2
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Auchterarder, Kinross, Blairgowrie
- Building rules
- Scotland
Internal pocket doors in Perth: what to know
A few practical points decide whether internal pocket doors suit a particular room and opening:
If your Perth home has a cramped en suite where the door clashes with the basin, a pocket door is worth measuring for before you consider moving the sanitaryware.
Before arranging a survey at your Perth home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
- Soft-close dampers can slow the door in its final few centimetres in both directions, stopping it slamming shut or bouncing back out of the pocket.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
Light and sun in Perth
In winter, Perth gets about 6 h 51 min of daylight against 17 h 43 min in June. Internal sliding and pocket doors help by keeping openings clear during the day and closing off rooms for warmth in the evening.
Internal pocket doors prices in Perth
The table shows guide prices for common sizes, supplied and fitted, including VAT. Your exact price is fixed in a written quote once the opening in your Perth home has been measured.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
How fitting works in Perth
A surveyor checks the doorway, the wall and the floor in your Perth home and talks through the glass or door finish. After you approve the written quote, the door is made typically 3–5 weeks after survey sign-off, depending on the door leaf and finish, and fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Perth?
In Scotland, fitting an internal sliding or pocket door is usually warrant-free; we use safety glass in glazed doors, and alterations to structural walls need a building warrant.
Which options matter for internal pocket doors?
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
Questions about internal pocket doors in Perth
Do I need building approval for internal pocket doors in Perth?
In Scotland a like-for-like replacement door usually needs no building warrant, but must meet the building standards; new openings need a warrant. We confirm the right route for your property at survey, so the paperwork is in place before fitting.
Are pocket doors suitable for bathrooms?
Pocket doors work well for bathrooms and en suites, particularly small ones where a swinging door clashes with a basin or toilet. A privacy hook lock with an emergency release gives you a lockable door. Bear in mind that a pocket door does not seal as tightly as a hinged door closing against stops on all sides, so a little more sound can pass through.
What is an internal pocket door?
An internal pocket door is an interior door that slides into a cavity built inside the wall instead of swinging on hinges. The leaf hangs from rollers on a concealed track at the top of a pocket frame, and the frame is boarded and plastered so the wall looks normal. When the door is open, only its edge and pull remain visible.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.