- Postcode district
- BA2
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Bradford-on-Avon, Keynsham, Trowbridge
- Building rules
- England
Is an internal pocket door a good fit for your home in Bath?
These are the points a surveyor will go through with you when you choose internal pocket doors for a home in Bath:
Before arranging a survey at your Bath home, check whether the wall beside the doorway carries radiators, sockets or pipes, because those decide whether internal pocket doors will fit.
In a Bath hallway where three or four doors open into the same small space, swapping one or two for pocket doors can stop them colliding with each other.
- When the door is fully open it disappears into the wall, leaving a clear doorway that makes two connected rooms feel like one larger space.
- Top-hung rollers carry the weight of the leaf from above, so there is no floor track to trip over, clean around or catch the vacuum cleaner on.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
How much sun will a door in Bath get?
With roughly 7 h 51 min of daylight on the shortest day in Bath, rooms in the middle of a house can feel gloomy in winter. A glazed internal door shares light from the brightest room without losing the separation of a closed door.
Internal pocket doors prices in Bath
These are guide prices for fitted doors, including VAT. They run from an entry-level system to a premium one at the same size; the survey confirms which suits your opening.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
Timescales for internal pocket doors in Bath
Surveys in the BA2 district are booked at a time that suits you. Lead time is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish; on fitting day the track or pocket is installed, the door is hung and adjusted, and the area is left clean. Fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Internal doors are generally outside the Building Regulations notification rules, with two things to watch: we only use safety glazing in glass doors, in line with Approved Document K, and any change to a load-bearing wall needs structural advice and Building Control approval.
Options to consider for your internal pocket door
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Bathroom privacy lock. A hook lock with an emergency release, designed for doors that slide rather than swing.
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
Questions about internal pocket doors in Bath
Do you fit internal pocket doors in Bath?
Yes. We survey and fit internal pocket doors in Bath and across Somerset, including nearby Bradford-on-Avon and Keynsham. Start with a guide price online or call us, and we will arrange a free survey for a new or replacement door.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
Do pocket doors need a floor track?
No, the pocket doors we fit hang from rollers on a top track, so the floor stays clear and level through the doorway. A small guide at the mouth of the pocket keeps the leaf running straight without a groove across the floor. That makes them easy to clean around and suitable where the same flooring runs from room to room.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.