- Postcode district
- BA5
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Shepton Mallet, Glastonbury, Street
- Building rules
- England
What internal pocket doors offer homes in Wells
The right door depends on the opening, the room and the way you use the garden. Here is how internal pocket doors tend to work out in practice:
Where a Wells house has solid brick internal walls, a pocket door is still possible, but expect a new stud lining and more making good than in a timber partition.
Renovating a period property in Wells? Pocket doors can take panelled leaves that echo the existing doors, so the change looks considered rather than out of place.
- Top-hung rollers carry the weight of the leaf from above, so there is no floor track to trip over, clean around or catch the vacuum cleaner on.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- Reclaims the floor area a hinged door needs to swing, which in a small bathroom or cloakroom can be the difference between fitting a vanity unit and going without.
Planning glass for the light in Wells
In winter, Wells gets about 7 h 52 min of daylight against 16 h 35 min in June. Internal sliding and pocket doors help by keeping openings clear during the day and closing off rooms for warmth in the evening.
Typical costs for internal pocket doors around Wells
The table shows guide prices for common sizes, supplied and fitted, including VAT. Your exact price is fixed in a written quote once the opening in your Wells home has been measured.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
From survey to fitted door in Wells
A surveyor checks the doorway, the wall and the floor in your Wells home and talks through the glass or door finish. After you approve the written quote, the door is made typically 3–5 weeks after survey sign-off, depending on the door leaf and finish, and fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Wells?
Internal doors are generally outside the Building Regulations notification rules, with two things to watch: we only use safety glazing in glass doors, in line with Approved Document K, and any change to a load-bearing wall needs structural advice and Building Control approval.
Finishes and extras for internal pocket doors
- Soft-close dampers. Hidden dampers in the track that ease the door to a gentle stop at each end.
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
Questions about internal pocket doors in Wells
How soon can you survey in Wells?
Surveys in the BA5 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.
Do pocket doors need a floor track?
No, the pocket doors we fit hang from rollers on a top track, so the floor stays clear and level through the doorway. A small guide at the mouth of the pocket keeps the leaf running straight without a groove across the floor. That makes them easy to clean around and suitable where the same flooring runs from room to room.