- Postcode district
- SW12
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Tooting, Streatham, Clapham
- Building rules
- England
What external pocket sliding doors offer homes in Balham
A few practical points decide whether external pocket sliding doors suit a particular room and opening:
Solid brick, cavity block or timber frame: the way your Balham wall is built decides how the pocket is formed, which is why the survey looks at it closely.
If the wall beside your Balham patio opening is free of windows, radiators and sockets, it may be long enough to take a pocket so the panels disappear completely.
- Parked inside the wall, open panels are protected from weather and knocks, and garden furniture can sit right up to the edge of the opening.
- A removable access panel on the inside of the pocket wall lets the rollers be reached and adjusted without opening up the plaster.
- Pockets can be formed on one side or both, so a wide opening can part in the middle with panels sliding away in each direction.
Sunlight, glass and orientation in Balham
Daylight in Balham runs from about 7 h 50 min in December to 16 h 38 min in June, with the noon sun at roughly 15° and 62° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
External pocket sliding doors prices in Balham
Pricing does not change because you are in Balham: the ranges below include fitting, structural calculations and VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 2.1 m | 1 panel | £7,095–£8,595 |
| 2.4 m | 2 panels | £7,495–£9,195 |
| 6.0 m | 3 panels | £12,895–£15,795 |
See every size on the external pocket sliding doors page or try the guide price tool.
How fitting works in Balham
Surveys in the SW12 district are booked at a time that suits you. Once the opening is ready and measured, manufacture is typically 6–8 weeks from survey sign-off; on fitting day the frame is set level and sealed, and the panels are adjusted so they glide properly. Fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door.
Rules for external pocket sliding doors in England
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Finishes and extras for external pocket sliding doors
- Threshold. Low or flush thresholds, with the external drainage channel continuing past the pocket.
- Pocket side. A single pocket to one side, or pockets on both sides so a wide door parts in the middle.
- Colours. Single or dual colour powder coating, so the exposed edge of the panel matches the frame inside and out.
Questions about external pocket sliding doors in Balham
Do I need building approval for external pocket sliding doors in Balham?
In England a replacement door is a controlled fitting, so compliance is arranged through a competent person scheme installer or Building Control; new openings need a Building Regulations application. We confirm the right route for your property at survey, so the paperwork is in place before fitting.
How long does an external pocket door project take?
An external pocket door typically takes 6–8 weeks to make after survey sign-off, and the building work to form the opening and pocket typically takes 3–5 days before the door goes in. Fitting the door then takes 1–2 days. Engineer design and Building Regulations approval come first, so the whole project runs longer than a straight door swap.
How do you maintain rollers inside a wall pocket?
You maintain pocket door rollers through the access panel built into the inside of the pocket wall, which lets the track be vacuumed and the rollers adjusted without opening up the wall. Keep the outside drainage channel clear so water cannot back up into the pocket, and run the panels fully in and out now and then. If a panel starts to rub inside the pocket, a small roller height adjustment through the access panel usually cures it.
Do external pocket doors need Building Regulations approval?
External pocket doors need Building Regulations approval in England, because forming the opening and pocket is structural work needing an application, structural calculations (included in our guide prices), and usually a steel beam or lintel. If the steel bears on a party wall, the Party Wall etc. Act 1996 (England and Wales) may apply. Scotland needs a building warrant; Wales and Northern Ireland have their own building control rules.