- Postcode district
- KT3
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Kingston upon Thames, Surbiton, Wimbledon
- Building rules
- England
Is an external pocket sliding door a good fit for your home in New Malden?
These are the points a surveyor will go through with you when you choose external pocket sliding doors for a home in New Malden:
Solid brick, cavity block or timber frame: the way your New Malden wall is built decides how the pocket is formed, which is why the survey looks at it closely.
Want the whole width of your New Malden kitchen open to the garden but prefer the look of sliders to bifolds? A pocket gives you both, at the cost of more building work.
- With every panel slid into the wall, the full width of the opening is clear, so the room and terrace join without a fixed panel in the way.
- Parked inside the wall, open panels are protected from weather and knocks, and garden furniture can sit right up to the edge of the opening.
- A lined and drained pocket carries rainwater running along the track out of the wall, protecting the structure as well as the rollers.
Light and sun in New Malden
Daylight in New Malden runs from about 7 h 51 min in December to 16 h 37 min in June, with the noon sun at roughly 15° and 62° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
Guide prices for external pocket sliding doors in New Malden
Guide prices include the door, fitting and structural calculations, including VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 2.1 m | 1 panel | £7,095–£8,595 |
| 4.0 m | 2 panels | £9,895–£12,095 |
| 6.0 m | 3 panels | £12,895–£15,795 |
See every size on the external pocket sliding doors page or try the guide price tool.
Timescales for external pocket sliding doors in New Malden
A surveyor visits your New Malden home to check the wall, the structure above and the floor levels, and talks through glass and finish. Any building work is planned to the engineer's design, the door is made to the finished opening sizes — typically 6–8 weeks from survey sign-off — and fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door.
Do you need approval in New Malden?
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Choosing the specification
- Threshold. Low or flush thresholds, with the external drainage channel continuing past the pocket.
- Colours. Single or dual colour powder coating, so the exposed edge of the panel matches the frame inside and out.
- Pocket side. A single pocket to one side, or pockets on both sides so a wide door parts in the middle.
Questions about external pocket sliding doors in New Malden
How soon can you survey in New Malden?
Surveys in the KT3 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 6–8 weeks from survey sign-off.
How long does an external pocket door project take?
An external pocket door typically takes 6–8 weeks to make after survey sign-off, and the building work to form the opening and pocket typically takes 3–5 days before the door goes in. Fitting the door then takes 1–2 days. Engineer design and Building Regulations approval come first, so the whole project runs longer than a straight door swap.
How much wall do I need for an external pocket door?
An external pocket door needs a clear length of wall beside the opening at least as long as the panels that slide into it, plus a little for the frame. For a single 2 m panel that means just over 2 m of wall with no windows, radiators, sockets or pipes in it. A two-sided pocket splits the panels between both sides, so each side needs less length.
Do external pocket doors need Building Regulations approval?
External pocket doors need Building Regulations approval in England, because forming the opening and pocket is structural work needing an application, structural calculations (included in our guide prices), and usually a steel beam or lintel. If the steel bears on a party wall, the Party Wall etc. Act 1996 (England and Wales) may apply. Scotland needs a building warrant; Wales and Northern Ireland have their own building control rules.