- Postcode district
- SY21
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 2–4 weeks for uPVC or 4–6 weeks for aluminium, from survey sign-off
- Guide price
- From £1,995 inc VAT
- Nearby
- Newtown, Oswestry, Church Stretton
- Building rules
- Wales
What tilt and slide doors offer homes in Welshpool
Most homeowners choosing tilt and slide doors want the same things: more light, a clear view and a door that is easy to live with.
If a bedroom in your Welshpool home opens onto a balcony or garden, the tilt position on tilt and slide doors lets in fresh air at night without leaving the door open.
A kitchen in Welshpool that steams up while you cook can be aired by tilting the sash, which is quicker than reaching across the worktop to a window.
- When closed, the sash is drawn back into the frame and presses onto gaskets on all four edges, giving a window-like seal against draughts and driving rain.
- The tilt position opens a narrow gap at the top of the sash while the hardware holds it in place, so a room can be aired without leaving a door open.
- The sash moves forward and slides parallel in front of the fixed pane, so nothing swings into the room and the floor beside the door stays usable.
Planning glass for the light in Welshpool
Daylight in Welshpool runs from about 7 h 37 min in December to 16 h 52 min in June, with the noon sun at roughly 14° and 61° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
Guide prices for tilt and slide doors in Welshpool
Guide prices are the same across Powys: the fitted price depends on the size, system and specification, not your postcode. These figures are for a standard 2.1 m high door, fitted, including VAT and removal of an old door of similar size.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.5 m | 2 panels | £1,995–£2,495 |
| 1.8 m | 2 panels | £2,195–£2,695 |
| 2.1 m | 2 panels | £2,395–£2,895 |
See every size on the tilt and slide doors page or try the guide price tool.
Survey, manufacture and fitting around Welshpool
Once the opening is measured, nothing is ordered until you sign off the specification. Lead time is typically 2–4 weeks for uPVC or 4–6 weeks for aluminium, from survey sign-off. Our fitters protect floors, remove the old door, install and seal the new one and leave the area clean — usually 1 day for a straight swap in an existing opening for a door like this.
Rules for tilt and slide doors in Wales
Wales sets its own Building Regulations guidance, including Approved Document L (Wales) for energy. A replacement sliding door must meet those requirements and use safety glass, and we arrange compliance through a registered installer or the local Building Control service.
Choosing the specification
- Handle. An inside lever handle with a key lock, plus an outside pull handle or cylinder if the door is used from the garden.
- Sash side. A left or right opening sash, chosen to suit furniture, the patio layout and the way you walk out.
- Colours. White, woodgrain or coloured foils on uPVC; standard or RAL powder coats on aluminium.
Questions about tilt and slide doors in Welshpool
Do I need building approval for tilt and slide doors in Welshpool?
In Wales a replacement door must meet the Building Regulations as applied in Wales, arranged through a registered installer or Building Control. We confirm the right route for your property at survey, so the paperwork is in place before fitting.
How much does a tilt and slide patio door cost?
Tilt and slide patio doors start from a guide price of £1,995 for a 1.5 m two-panel door, fitted, inc VAT, at standard 2.1 m height. A 2.1 m door is a guide £2,395–£2,895, and a 3 m door is around £2,995. Aluminium frames, colour and triple glazing move the figure up, and the final price is fixed in a written quote after survey.
How wide can a tilt and slide door be?
A tilt and slide door in our range is typically about 1.5 m to 3 m wide overall, with one opening sash and one fixed panel. The sash size is set by the hardware's weight limit, which is lower than for inline or lift and slide systems. If you need a wider opening, a standard aluminium slider or a lift and slide door is the usual alternative.
How long does a tilt and slide door take?
A tilt and slide door typically takes 2–4 weeks to make in uPVC and 4–6 weeks in aluminium, from survey sign-off. Fitting typically takes 1 day for a straight swap in an existing opening, including removing the old door and making good. These are typical times rather than fixed promises, and the date is confirmed once the order is placed.