- Postcode district
- G81
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Erskine, Renfrew, Bearsden
- Building rules
- Scotland
Is an internal pocket door a good fit for your home in Clydebank?
These are the points a surveyor will go through with you when you choose internal pocket doors for a home in Clydebank:
Planning an open-plan kitchen in Clydebank but still want to close it off now and then? A double pocket door gives you both.
Renovating a period property in Clydebank? Pocket doors can take panelled leaves that echo the existing doors, so the change looks considered rather than out of place.
- Privacy hook locks made for sliding leaves give a bathroom or en suite a door that locks from inside and can still be released from outside in an emergency.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- Flush pulls sit level with the face of the door so the leaf can slide fully into the pocket, with a small edge pull to draw it back out again.
Light and sun in Clydebank
With roughly 6 h 58 min of daylight on the shortest day in Clydebank, rooms in the middle of a house can feel gloomy in winter. A glazed internal door shares light from the brightest room without losing the separation of a closed door.
Guide prices for internal pocket doors in Clydebank
Guide prices are the same across Glasgow and Dunbartonshire. They cover the door supplied and fitted into a prepared opening, including VAT, with options itemised in your quote.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
From survey to fitted door in Clydebank
A surveyor checks the doorway, the wall and the floor in your Clydebank home and talks through the glass or door finish. After you approve the written quote, the door is made typically 3–5 weeks after survey sign-off, depending on the door leaf and finish, and fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Do you need approval in Clydebank?
Internal doors do not normally need a building warrant in Scotland. We only supply safety glass for glazed doors, and any change to a structural wall would need a warrant, so we check the wall at survey.
Choosing the specification
- Double pocket door. Two leaves sliding into opposite sides of the opening for a wider, centred doorway.
- Bathroom privacy lock. A hook lock with an emergency release, designed for doors that slide rather than swing.
- Glazed leaf. A door with safety glass panels that borrows daylight from one room for another.
Questions about internal pocket doors in Clydebank
Can you match other doors and windows in my Clydebank home?
Usually, yes. Most aluminium and uPVC systems come in standard RAL colours and finishes, and we can quote dual colour where the inside and outside need to differ. Bring photos of existing frames to the survey.
How much does an internal pocket door cost?
Our guide price for a fitted internal pocket door is £895–£1,595 for a single and £1,695–£2,795 for a double, inc VAT at standard height. Where your door falls in that range depends on the leaf, the hardware, the wall construction and how much making good is needed. The final figure is fixed in a written quote after we have surveyed the wall.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.