- Postcode district
- TW20
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 3–5 weeks after survey sign-off, depending on the door leaf and finish
- Guide price
- From £895 inc VAT
- Nearby
- Slough, Feltham, Hayes
- Building rules
- England
Is an internal pocket door a good fit for your home in Egham?
Here is what to weigh up if you are considering internal pocket doors for a home in Egham:
Renovating a period property in Egham? Pocket doors can take panelled leaves that echo the existing doors, so the change looks considered rather than out of place.
In an Egham hallway where three or four doors open into the same small space, swapping one or two for pocket doors can stop them colliding with each other.
- When the door is fully open it disappears into the wall, leaving a clear doorway that makes two connected rooms feel like one larger space.
- A double pocket door, with two leaves parting from the centre, opens up a wide doorway between a kitchen and a living area without any doors standing in the room.
- Privacy hook locks made for sliding leaves give a bathroom or en suite a door that locks from inside and can still be released from outside in an emergency.
Daylight in Egham and what it means for your glass
In winter, Egham gets about 7 h 50 min of daylight against 16 h 38 min in June. Internal sliding and pocket doors help by keeping openings clear during the day and closing off rooms for warmth in the evening.
How much do internal pocket doors cost in Egham?
Guide prices are the same across Surrey. They cover the door supplied and fitted into a prepared opening, including VAT, with options itemised in your quote.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| Single pocket door | 1 leaf | £895–£1,595 |
| Double pocket door | 2 leaves | £1,695–£2,795 |
See every size on the internal pocket doors page or try the guide price tool.
From survey to fitted door in Egham
Surveys in the TW20 district are booked at a time that suits you. Lead time is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish; on fitting day the track or pocket is installed, the door is hung and adjusted, and the area is left clean. Fitting usually takes 1–2 days, plus drying time before new plaster can be decorated.
Rules for internal pocket doors in England
Internal doors are generally outside the Building Regulations notification rules, with two things to watch: we only use safety glazing in glass doors, in line with Approved Document K, and any change to a load-bearing wall needs structural advice and Building Control approval.
Specification choices for internal pocket doors in Egham
- Single pocket door. One leaf sliding into one side of the wall, the usual choice for en suites and cupboards.
- Flush and edge pulls. Recessed pulls in the door face plus an edge pull, so the leaf can disappear fully into the pocket.
- Bathroom privacy lock. A hook lock with an emergency release, designed for doors that slide rather than swing.
Questions about internal pocket doors in Egham
How soon can you survey in Egham?
Surveys in the TW20 district are booked at a time that suits you, and we offer survey dates when we reply to your enquiry. After you approve the written quote, manufacture is typically 3–5 weeks after survey sign-off, depending on the door leaf and finish.
How much wall space does a pocket door need?
A pocket door needs a length of clear wall beside the opening that is roughly the width of the door, plus a little extra for the frame. A double pocket door needs that space on both sides. The pocket section must be free of radiators, sockets, switches, pipes and cables, which is often the deciding factor in whether a particular doorway works.
Can I put a light switch on the wall with the pocket?
Not on the pocket section itself, because the door slides through that cavity and there is nowhere to run a cable or fix a back box. Switches and sockets can usually move to the other side of the doorway or to an adjoining wall. We point out any that need moving at survey, and an electrician should relocate them before the pocket frame goes in.
Can a pocket door be fitted into an existing wall?
Yes, a pocket door can usually be fitted into an existing wall, but it involves opening up the wall beside the doorway. In a stud partition we remove the plasterboard, fit the pocket frame and board it again. In a masonry wall the usual approach is a new stud lining, and if the wall is load-bearing, forming the pocket becomes structural work that needs proper assessment and approval first.