- Postcode district
- SP10
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Winchester, Amesbury, Newbury
- Building rules
- England
External pocket sliding doors in Andover: what to know
The right door depends on the opening, the room and the way you use the garden. Here is how external pocket sliding doors tend to work out in practice:
Want the whole width of your Andover kitchen open to the garden but prefer the look of sliders to bifolds? A pocket gives you both, at the cost of more building work.
If the only wall beside your Andover opening is shared with a neighbour, check the pocket design and any steel bearing on it early, as the Party Wall etc. Act 1996 (England and Wales) may apply.
- A lined and drained pocket carries rainwater running along the track out of the wall, protecting the structure as well as the rollers.
- Parked inside the wall, open panels are protected from weather and knocks, and garden furniture can sit right up to the edge of the opening.
- When closed, a pocket door looks like a large-paned slider, with slim meeting stiles and plenty of glass instead of the many frames of a folding door.
Planning glass for the light in Andover
Daylight in Andover runs from about 7 h 52 min in December to 16 h 35 min in June, with the noon sun at roughly 15° and 62° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
How much do external pocket sliding doors cost in Andover?
Guide prices include the door, fitting and structural calculations, including VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 1 panel | £6,595–£8,095 |
| 2.1 m | 1 panel | £7,095–£8,595 |
| 3.6 m | 2 panels | £9,295–£11,395 |
See every size on the external pocket sliding doors page or try the guide price tool.
From survey to fitted door in Andover
Surveys in the SP10 district are booked at a time that suits you. Once the opening is ready and measured, manufacture is typically 6–8 weeks from survey sign-off; on fitting day the frame is set level and sealed, and the panels are adjusted so they glide properly. Fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door.
Do you need approval in Andover?
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Options to consider for your external pocket sliding door
- Pocket side. A single pocket to one side, or pockets on both sides so a wide door parts in the middle.
- Colours. Single or dual colour powder coating, so the exposed edge of the panel matches the frame inside and out.
- System type. Standard aluminium, slimline or lift and slide pocket systems, chosen to suit panel weight and sightlines.
Questions about external pocket sliding doors in Andover
Is the price different in Andover?
No. Guide prices for external pocket sliding doors are the same across mainland Britain, including Andover. The fitted price depends on size, system, glass and finish, and any structural work, all fixed in your written quote after survey.
How do you maintain rollers inside a wall pocket?
You maintain pocket door rollers through the access panel built into the inside of the pocket wall, which lets the track be vacuumed and the rollers adjusted without opening up the wall. Keep the outside drainage channel clear so water cannot back up into the pocket, and run the panels fully in and out now and then. If a panel starts to rub inside the pocket, a small roller height adjustment through the access panel usually cures it.
Do external pocket doors need Building Regulations approval?
External pocket doors need Building Regulations approval in England, because forming the opening and pocket is structural work needing an application, structural calculations (included in our guide prices), and usually a steel beam or lintel. If the steel bears on a party wall, the Party Wall etc. Act 1996 (England and Wales) may apply. Scotland needs a building warrant; Wales and Northern Ireland have their own building control rules.
How much wall do I need for an external pocket door?
An external pocket door needs a clear length of wall beside the opening at least as long as the panels that slide into it, plus a little for the frame. For a single 2 m panel that means just over 2 m of wall with no windows, radiators, sockets or pipes in it. A two-sided pocket splits the panels between both sides, so each side needs less length.