- Postcode district
- BA5
- Survey
- Free for new and replacement doors
- Typical lead time
- Typically 6–8 weeks from survey sign-off
- Guide price
- From £6,595 inc VAT
- Nearby
- Shepton Mallet, Glastonbury, Street
- Building rules
- England
Is an external pocket sliding door a good fit for your home in Wells?
The right door depends on the opening, the room and the way you use the garden. Here is how external pocket sliding doors tend to work out in practice:
If the only wall beside your Wells opening is shared with a neighbour, check the pocket design and any steel bearing on it early, as the Party Wall etc. Act 1996 (England and Wales) may apply.
Solid brick, cavity block or timber frame: the way your Wells wall is built decides how the pocket is formed, which is why the survey looks at it closely.
- A lined and drained pocket carries rainwater running along the track out of the wall, protecting the structure as well as the rollers.
- Parked inside the wall, open panels are protected from weather and knocks, and garden furniture can sit right up to the edge of the opening.
- Pockets can be formed on one side or both, so a wide opening can part in the middle with panels sliding away in each direction.
How much sun will a door in Wells get?
Daylight in Wells runs from about 7 h 52 min in December to 16 h 35 min in June, with the noon sun at roughly 15° and 62° respectively. Use that to choose your glass: standard low-E double glazing for north and east elevations, and consider solar-control or triple glazing for sunny south and west walls.
How much do external pocket sliding doors cost in Wells?
Pricing does not change because you are in Wells: the ranges below include fitting, structural calculations and VAT. They include forming the opening and the pocket in the wall; Building Control fees are set by your council and are extra.
| Overall width | Typical panels | Guide price (fitted, inc VAT) |
|---|---|---|
| 1.8 m | 1 panel | £6,595–£8,095 |
| 3.0 m | 2 panels | £8,395–£10,295 |
| 3.6 m | 2 panels | £9,295–£11,395 |
See every size on the external pocket sliding doors page or try the guide price tool.
Timescales for external pocket sliding doors in Wells
A surveyor visits your Wells home to check the wall, the structure above and the floor levels, and talks through glass and finish. Any building work is planned to the engineer's design, the door is made to the finished opening sizes — typically 6–8 weeks from survey sign-off — and fitting usually takes 3–5 days of building work to form the opening and pocket, then 1–2 days to fit the door.
Rules for external pocket sliding doors in England
A new or wider opening in England needs Building Control approval for the structural work as well as compliance for the door itself under Approved Documents L and K. Expect structural calculations, a steel beam and, where a party wall is involved, notices under the Party Wall etc. Act 1996.
Choosing the specification
- Pocket side. A single pocket to one side, or pockets on both sides so a wide door parts in the middle.
- Glass. Double or triple glazed safety glass, with laminated or solar-control units as needed.
- Internal finish. Plastered, panelled or tiled finishes on the pocket wall, with the access panel set discreetly into it.
Questions about external pocket sliding doors in Wells
Do I need building approval for external pocket sliding doors in Wells?
In England a replacement door is a controlled fitting, so compliance is arranged through a competent person scheme installer or Building Control; new openings need a Building Regulations application. We confirm the right route for your property at survey, so the paperwork is in place before fitting.
How much do external pocket sliding doors cost?
External pocket sliding doors start from a guide price of £6,595 for a 1.8 m single-panel door, fitted, inc VAT, at standard 2.1 m height, including forming the wall pocket. A 3 m two-panel door is a guide £8,395–£10,295, and a 6 m three-panel door is around £12,895. Wall construction, glass and finish affect the figure, which is fixed in a written quote after survey.
How wide can an external pocket sliding door be?
An external pocket sliding door in our range typically gives a clear opening of about 1.8 m to 6 m, using one panel at the narrow end and two or three panels on wider doors. Wider openings usually use pockets on both sides, or a multi-track pocket so the panels stack inside the wall. Sizes are confirmed after survey and the engineer's design.
How do you maintain rollers inside a wall pocket?
You maintain pocket door rollers through the access panel built into the inside of the pocket wall, which lets the track be vacuumed and the rollers adjusted without opening up the wall. Keep the outside drainage channel clear so water cannot back up into the pocket, and run the panels fully in and out now and then. If a panel starts to rub inside the pocket, a small roller height adjustment through the access panel usually cures it.